Cabletron Systems MT8-MIM Spezifikationen Seite 73
- Seite / 192
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
7-1
Chapter 7
Fast Ethernet Network
Requirements
This chapter provides test parameters and specification requirements for Fast Ethernet network
cabling.
100BASE-TX
All Cabletron Systems 100BASE-TX products require that installed facility cabling
and cable hardware meet the following minimum specifications. If a network
cabling installation is not within the limitations presented here, the operation of
the 100BASE-TX products may be affected.
Cable Type
The operation of a 100BASE-TX network is more demanding than that of standard
Ethernet, and high-quality cables are required. The 100BASE-TX specification for
Fast Ethernet networks requires UTP cabling Category 5. Categories of UTP
cabling below Category 5 may not meet the quality requirements of the
networking specification, and may therefore be unable to meet the tested
characteristics listed below.
The Category of cabling used in a network installation is dependent upon all the
components that make up the cabling run. If an installation utilizes Category 5
cabling, and the wallplates and patch panels to which that cabling is connected
are Category 3 compliant, the cable does not meet the EIA/TIA end-to-end
specifications for a Category 5 installation.
NOTE
Due to the construction of the connectors and organization of
wires, the 25-pair RJ21 connector is not Category 5 compliant.
- Cabletron Systems 1
- Cabling Guide 1
- Contents 5
- Chapter 11 FDDI Media 9
- Introduction 11
- 1-2 Document Organization 12
- Document Conventions 13
- Additional Assistance 14
- Related Documentation 14
- Cabling Terms 15
- 2-2 Physical Components 16
- Connector 17
- 2-4 Physical Components 18
- Physical Components 2-5 19
- Test Characteristics 20
- Test Characteristics 2-7 21
- 2-8 Test Characteristics 22
- Relevant Specifications 23
- Ethernet Media 25
- 4-2 Cabling Types 26
- Coaxial Cable 27
- 4-4 Cabling Types 28
- Unshielded Twisted Pair (UTP) 29
- 4-6 Cabling Types 30
- Cabling Types 4-7 31
- 4-8 Cabling Types 32
- Cabling Types 4-9 33
- 4-10 Cabling Types 34
- Cabling Types 4-11 35
- 4-12 Cabling Types 36
- Cabling Types 4-13 37
- Cabling Types 4-15 39
- 4-16 Cabling Types 40
- 4-18 Connector Types 42
- 4-20 Connector Types 44
- Annular Ring 44
- TRANSCEIVER 45
- 4-22 Connector Types 46
- UTP Cable 47
- 4-24 Connector Types 48
- Connector Types 4-25 49
- TransmitTransmit 50
- ReceiveReceive 50
- Connector Types 4-27 51
- Connector Types 4-29 53
- 4-30 Connector Types 54
- Ethernet Network Requirements 55
- Other Considerations 57
- 10BASE-F (Multimode) 58
- Insertion Loss 59
- Ethernet FOIRL (Single Mode) 60
- Termination 62
- Connectors/Taps 62
- 10BASE5 (Coaxial Cable) 63
- Grounding 64
- Full-Duplex Ethernet Network 65
- Requirements 65
- Insertion Loss (Attenuation) 66
- Fast Ethernet Network 73
- 100BASE-FX (Multimode) 76
- Hybrid Installations 77
- Repeater Classes 78
- Buffered Uplinks 79
- 7-8 Hybrid Installations 80
- 8-4 100BASE-TX 84
- 8-6 100BASE-FX (Multimode) 86
- 9-2 Cabling Types 88
- Cabling Types 9-3 89
- 9-4 Cabling Types 90
- 9-6 Cabling Types 92
- Cabling Types 9-7 93
- Cabling Types 9-9 95
- Connector Types 9-11 97
- 9-12 Connector Types 98
- Connector Types 9-13 99
- BK RE GR OR 100
- Unshielded Twisted Pair Cable 101
- Fiber Optics 103
- Token Ring Media 104
- 9-18 Connector Types 104
- Chapter 10 105
- Impedance 106
- Attenuation 106
- Link Length 107
- Trunk Cable Length 108
- Cable Type 109
- Crosstalk 110
- FDDI Media 115
- 11-2 Cabling Types 116
- Cabling Types 11-3 117
- 11-4 Cabling Types 118
- Shielded Twisted Pair (STP) 119
- 11-6 Cabling Types 120
- STP Cable Quality 121
- Cabling Types 11-9 123
- 11-10 Cabling Types 124
- Connector Types 125
- 11-12 Connector Types 126
- 11-14 Connector Types 128
- Connector Types 11-15 129
- 11-16 Connector Types 130
- FDDI Network Requirements 131
- Emitted Power 132
- TP -PMD (UTP) 134
- TP-PMD (STP) 135
- 12-6 TP-PMD (STP) 136
- Cabling Devices 137
- Hardware Mounting 138
- Enclosed Equipment Cabinet 139
- Cable Termination 140
- Harmonica 141
- Punchdown Block 142
- Distribution Box 143
- Wallplate 144
- Facility Cable Management 145
- 12 11 10 9 8 76543 21 147
- Innerduct 148
- Latching Duct 148
- Labeling Tape 149
- Ty-Wraps and Adhesive Anchors 150
- Connecting and Terminating 151
- 14-2 Ethernet 152
- Ethernet 14-3 153
- 14-4 Ethernet 154
- Ethernet 14-5 155
- 14-6 Ethernet 156
- ST Connector 157
- 14-8 Ethernet 158
- Token Ring 159
- 14-10 Token Ring 160
- Token Ring 14-11 161
- Token Ring MIC 162
- 14-14 FDDI 164
- FDDI 14-15 165
- FDDI MIC 166
- FDDI 14-17 167
- SC Connector 168
- FDDI 14-19 169
- 14-20 FDDI 170
- Charts and Tables 171
- A-2 Ethernet 172
- Ethernet A-3 173
- Token Ring A-5 175
- A-6 FDDI 176
- Glossary-1 177
- Attenuation to Card 178
- Glossary-2 178
- Glossary-3 179
- Channel to Crosstalk 179
- CSMA/CD to Dual Attached 180
- Glossary-4 180
- Glossary-5 181
- Dual Homing to FNB 181
- Frame to Interface 182
- Glossary-6 182
- Glossary-7 183
- Internet to MAU 183
- Mbps to NVRAM 184
- Glossary-8 184
- Glossary-9 185
- Octet to Redundant 185
- Relay to SIMM 186
- Glossary-10 186
- Glossary-11 187
- Switch to UTP 188
- Glossary-12 188
- Numerics 189
Verwandte Produkte und Handbücher für Vernetzung Cabletron Systems MT8-MIM
Vernetzung Cabletron Systems E2100 Spezifikationen
(233 Seiten)
(233 Seiten)
(87 Seiten)
Vernetzung Cabletron Systems MT8-MIM Spezifikationen
(114 Seiten)
(114 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.080 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern