Cabletron Systems CSX400-DC Betriebsanweisung Seite 82
- Seite / 275
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Installation
68 CSX400 and CSX400-DC User’s Guide
Connecting the CSX400 to the Power Source
To connect the CSX400 to the power source, perform the following steps:
1. Plug the power cord into the back panel of the CSX400.
2. Plug the other end of the power cord into a grounded wall outlet.
3. Verify that the PWR LED is on, indicating that the CSX400 is receiving power. After the
CSX400 runs a self test, the CPU LED blinks green indicating normal operation. If the LED
remains red, the processor is faulty; contact Cabletron Systems Technical Support (refer to
Getting Help in Chapter 1.)
4. Proceed to Chapter 7 to configure the CSX400.
NOTE
The CSX400 has a universal power supply. This allows you to connect the CSX400 to
power sources of 100–125 and 200–240 Vac, 50/60 Hz.
- CSX400 AND CSX400-DC 1
- USER’S GUIDE 1
- FCC Notice 3
- DOC Notice 3
- DECLARATION OF CONFORMITY 6
- Contents 14
- Introduction 15
- Document Conventions 17
- Getting Help 18
- About the CSX400 19
- Ethernet LAN Connection 21
- Optional Features 22
- CSX400 Firmware Support 22
- WAN Protocols 23
- Firmware Data Compression 24
- Inverse Multiplexing (IMUX) 24
- DHCP and NAT 25
- Point-to-Point Protocol (PPP) 26
- PAP and CHAP Security 26
- Multilink Protocol 27
- Telephone Switch Support 28
- ISDN Back-up 29
- Bridging and Routing 30
- System Passwords 32
- SNMP MIB Support 33
- Cabletron Enterprise MIBs 34
- SNMP Trap Support 34
- Arranging ISDN Service 37
- ISDN BRI Line Configuration 38
- ISDN BRI Configurations 39
- Telephone Switch Parameters 40
- Collect Network Information 44
- Names and Passwords 44
- ISDN Line Information 45
- Network Information Diagrams 46
- Network Information Tables 52
- Sample Configuration 56
- Names and Passwords Example 61
- Ethernet Cabling Requirements 63
- 10BASE-T Twisted Pair Network 64
- Multimode Fiber Optic Network 65
- 10BASE2 Coaxial Cable Network 67
- Transceiver Requirements 67
- Installation 69
- Installing Interface Modules 70
- ETHERNET 1 71
- ETHERNET 2 71
- Removing the CSX400 Cover 72
- Removing the CSX400-DC Cover 73
- CSX-COMP/ENCR Installation 76
- Installing the CSX400 77
- Tools Required 78
- Rackmount Brackets (2) 79
- Screws (4) 80
- Rackmount 80
- Brackets (2) 80
- DC Input Power Strip 84
- 48 or 60 Vdc 84
- Power Source 84
- CSX400 configuration 87
- Ethernet Configuration 88
- QuickSET 114
- Firewall Configuration Window 115
- Routing Configuration Window 121
- IP Routing Configuration 122
- IPX Routing Configuration 122
- Host Map Window 123
- Figure 43 Redirector Window 126
- QuickSET Pull-Down Menus 131
- Firmware Upgrade Menu 133
- Advanced Configuration Menu 136
- Management 139
- Local Management Overview 140
- COMMAND FIELDS 141
- DISPLAY FIELDS 141
- INPUT FIELDS 141
- SELECTION FIELDS 141
- EVENT MESSAGE FIELD 141
- Accessing Local Management 146
- Main Menu Screen 147
- Setup Menu Screen 148
- System Level Screen 149
- Setting the System Date 152
- Setting the System Time 152
- Setting the Host IP Address 153
- Setting the Subnet Mask 153
- Setting the Default Gateway 153
- Setting the Default Interface 154
- SNMP Community Names Screen 155
- Setting SNMP Community Names 156
- SNMP Traps Screen 157
- Flash Download Screen 159
- RUNTIME Download 161
- BOOTPROM Download 161
- Bridge Setup Screen 163
- Bridge_Port 164
- Router Setup Screen 166
- IP Configuration Screen 167
- IP General Config Screen 168
- IPX Configuration Screen 176
- Entering the IPX Address 179
- IPX Routing over Frame Relay 181
- Enabling RIP on a Port 184
- WAN Setup 186
- MIB Navigator 191
- MIB Navigator Screen 192
- Navigation Commands 195
- MIBNav-> ctron 196
- MIBNav-> next /1/3/6/1/2/1 198
- MIBNav-> pwd 198
- Other Commands 204
- MIBNav-> done 217
- Connection closed 217
- Troubleshooting 219
- Troubleshooting the LAN 222
- Troubleshooting the WAN 223
- Status 1 (STS1) LED is RED 224
- Status 1 (STS1) LED is AMBER 225
- Status 1 (STS1) LED is GREEN 225
- Status 2 (STS2) LED is OFF 226
- Status 2 (STS2) LED is AMBER 227
- Status 2 (STS2) LED is GREEN 227
- WPIM-HDSL Installed in CSX400 228
- WPIM-S/T Installed in CSX400 228
- If Bridging 229
- If TCP/IP Routing 229
- EPIM-F1 and EPIM-F2 232
- Connector Type 235
- Grounding 235
- EPIM-A and EPIM-X (AUI Port) 236
- WPIM Cable Specifications 237
- WPIM Cable Specifications 238
- WPIM-SY interface cables 239
- WPIM-SY 239
- WPIM-DDS 247
- WPIM-DI interface cables 250
- WPIM-HDSL 251
- WPIM-S/T 252
- TELECOM — FCC Part 68, CS-03 255
- Glossary 265
- POWER SUPPLY CORD 275
- GERMAN: 275
- SPANISH: 275
Verwandte Produkte und Handbücher für Vernetzung Cabletron Systems CSX400-DC
Vernetzung Cabletron Systems MT8-MIM Spezifikationen
(192 Seiten)
(192 Seiten)
Vernetzung Cabletron Systems E2100 Spezifikationen
(233 Seiten)
(233 Seiten)
(87 Seiten)
Vernetzung Cabletron Systems MT8-MIM Spezifikationen
(114 Seiten)
(114 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern